A chest of drawers goes together well when you do four things in order: prepare the space and sort the parts, build the carcass (the outer box) loosely until it is square, fit the drawer slides level, and anchor the finished unit to the wall. Most sticking drawers trace back to one skipped step, usually tightening too early or slides fitted out of level. Our Me&Co chests come with assembly instructions written to be hassle-free and anti-rust hardware, so the steps below are the ones that matter most when you build one at home.
TL;DR
- Clear a flat area, lay down a blanket and sort every fitting before you touch a panel.
- Keep the carcass screws and cam locks slightly loose until the box is square, then tighten.
- Fit drawer slides level and parallel on both sides. Uneven slides are the main reason drawers stick.
- Test every drawer, then anchor the chest to the wall, especially in a child’s room.
- Plan on a couple of hours the first time, and build with a second person for larger pieces.
Table of Contents
- Before you start: space, tools and parts
- Step 1: Build the carcass loosely
- Step 2: Build the drawer boxes
- Step 3: Fit the drawer slides
- Step 4: Fit the fronts and handles
- Step 5: Test, adjust and anchor
- Bed frame assembly: the same logic, a different order
- Mistakes that cost the most time
- Why a well-made flat pack makes assembly easier
- Our view: build it once, build it right
- FAQ
- Sources
Before you start: space, tools and parts
The best assembly starts on the floor, not with the first screw. Clear an area bigger than the finished chest, about two metres by two metres is comfortable, and spread a blanket or an old duvet over it. The blanket protects the panels from scratches, and the panels are what you will see every day.
Open the box and lay the parts out. Match each panel and each bag of fittings to the parts list in your instructions. Sort screws, dowels, cam locks and cam bolts into a tray or a muffin tin, so nothing rolls away. If you are missing a part, stop here and contact the seller before you build anything. Finding out at step nine is far more frustrating.
For most flat-pack chests you need:
- A Phillips screwdriver, or a drill/driver with the right bits (set it to low torque so you do not strip the screw heads or crush the board).
- A flat screwdriver for turning cam locks.
- A rubber mallet for seating dowels.
- A small spirit level and a tape measure.
- A pencil, for marking positions.
South African DIY builders making a chest from scratch also rely on a drill/driver with assorted bits and a countersink bit, as Home DZINE’s chest of drawers project shows. A flat-pack chest is simpler, but the same tools make it easier.
How long will it take?
Give yourself a relaxed afternoon, or at least a couple of hours, the first time. A chest with several drawers has many small tasks: the carcass, then every drawer box, every slide, every front and every handle. The frame standing up feels like the finish line. It is closer to the halfway mark. If the chest is big, ask someone to help for the lifting and the final stand-up.
Step 1: Build the carcass loosely
The carcass is the outer box: two sides, a top, a base and usually a back panel. Follow the order in your instructions, because panels often only fit one way round.
- Check which face of each panel is the finished one. Pre-drilled holes usually sit on the inside, so the finished face shows on the outside.
- Tap the dowels into the edge holes with the mallet. They should go in snugly, not be forced.
- Join the side panels to the base and top. Insert the cam bolts, then turn the cam locks only until they just grip.
- Leave every fixing slightly loose. This is the step people most often rush. A box tightened out of square cannot be fully corrected later.
Square it before you tighten
Slide the back panel in place, then measure the two diagonals from corner to corner. When both measurements match, the box is square. If one is longer, push gently on the longer diagonal until they are equal. Only then tighten the cam locks fully and fix the back panel with its nails or screws. A square carcass is what lets drawers sit flush and glide.
The back panel is thin and it matters. It is what stops the whole unit from twisting sideways over the years, so do not skip nails or leave it half fixed.
Step 2: Build the drawer boxes
Each drawer is a small box of its own: two sides, a front, a back and a base that slides into a groove. Work on one drawer at a time and finish it before starting the next, so you do not mix up parts.
- Join the sides to the front first, then add the back.
- Slide the drawer base into its groove before closing the last side. On many designs it cannot go in afterwards.
- Check that the drawer box is square, using the same diagonal trick on a smaller scale.
If you want to see why the tolerances are so small, look at how a hand-built drawer is sized. In Wood Central’s chest of drawers article, the drawer sides are cut 16mm narrower than the drawer front so the drawer can clear the cabinet sides and the slides. Millimetres decide whether a drawer glides or catches. That is also why factory-drilled flat-pack parts are convenient: the hard measuring is already done for you.
Step 3: Fit the drawer slides
Drawer slides, also called runners, are the metal or plastic rails the drawers travel on. Each one comes in two parts: one section screws to the drawer side and the other to the inside of the carcass. This is where most assembly goes wrong, so take your time.
Keep both sides identical
The rule is simple: the left and right slides must sit at exactly the same height and the same distance from the front edge. Measure from the base or from the bottom of the drawer above, mark with a pencil on both sides, and check with the level before you screw.

Home DZINE’s guide for a dresser build shows how precise this is. It mounts the carcass-side runners along a marked line for each drawer and uses 12mm screws for the drawer sides and 16mm screws for the cabinet sides, so the screws never poke through the board. If your flat-pack chest includes its own screws, use only those. A screw that is too long can break through the face of a drawer or panel.
Mount the drawer-side section
Fix the drawer-side section flush with the back of the drawer front. Keep it at the same height on both drawer sides. Then slide the drawer in, starting from the bottom drawer and working up. The bottom drawer is the easiest to test, and fitting the top drawer last means you are never reaching over finished work.
Common slide mistakes
- One side higher than the other. The drawer tilts and drags. Re-measure and move the slide.
- Slides set too far forward or back. The drawer front will not sit flush. Check the distance from the front edge on both sides.
- Over-tightened screws. On particleboard, a screw driven too hard strips the hole. Stop when it is snug.
- Slides not parallel. If the gap between them is wider at the back than the front, the drawer racks and jams.
Step 4: Fit the fronts and handles
Hang the drawer fronts last, after the boxes run smoothly. Most flat-pack drawers use fixings that let you adjust the front a little. Hold a front in position, check the gaps around it are even, and tighten. Aim for a gap of equal width on all sides. Then add the handles. Measure the hole spacing against the handle and mark it with a pencil before drilling or screwing, so every handle lines up.
Step 5: Test, adjust and anchor
Before you throw away the packaging, run a five-minute check:
- Open and close every drawer slowly, then quickly.
- Push the top corner of the unit sideways. It should not wobble or lean.
- Check every cam lock is seated and every screw is snug.
- Check the chest stands flat. If it rocks, shift it or adjust the feet.
If a drawer sticks
A drawer that jams at the back is usually slightly too wide for the slides or the carcass is out of square. First, loosen the cam locks a little, re-square the box and tighten again. If the slide is the problem, adjust it by a millimetre or two and re-test. Wood Central describes a more hands-on fix for hand-built drawers: thin timber shims rubbed in at the rear under the drawer bottom, then trimmed flush. For a flat-pack chest, though, the cause is nearly always a loose or unlevel fixing, so check the basics first.
Anchor it to the wall
A chest of drawers can tip forward when drawers are pulled open, and children climbing on one is a known hazard. The US Consumer Product Safety Commission publishes a guide to securing furniture and TVs to protect children that recommends anchoring furniture against tip-over. Fit the anti-tip strap or bracket that comes with the unit, or buy one if it does not. Screw it into a wall stud or the right masonry plug, not a plastic drywall anchor. Our guide on anchoring furniture to wall studs explains the difference. Before you drill, make sure there are no pipes or electrical cables behind the spot. If you are unsure, ask a qualified electrician or plumber to check. Do this in a child’s room first.

Bed frame assembly: the same logic, a different order
People who search for chest of drawers assembly often have a bed to build in the same weekend, so here is how the approach carries over.
- Lay out and sort. Same blanket, same tray, same parts check.
- Build the base frame loosely. Join the headboard, footboard and side rails with the bolts supplied, hand-tight only. Frames need to settle before they are locked.
- Fit the centre support. Most double and larger beds have a central rail with legs. Fit it before the slats, because it carries the load in the middle.
- Check the frame is square and level. Measure the diagonals, as you did for the chest, and tighten fully.
- Place the slats. Space them evenly, with the curve facing up if they are bowed, and secure with the end caps or brackets supplied.
- Test before the mattress goes on. Press down on the frame at each corner and in the middle. Nothing should creak or shift.
A bed is heavy and awkward, so do it with a second person. Our guide to assembling a flat-pack wardrobe follows the same rhythm, and the general flat-pack furniture assembly guide covers the habits that apply to every piece. If you are placing the finished chest in a compact room, these decorating ideas for small bedrooms help you decide where it fits and what goes on top.
Mistakes that cost the most time
- Tightening too early. It locks in a twisted box. Keep everything loose until the diagonals match.
- Mixing similar panels. Sort parts by the label or letter in the manual, not by how alike they look.
- Forcing a part. If a dowel or cam will not seat, the panel is probably the wrong way round or the wrong piece.
- Assembling on the floor where it will stand. Build near the final spot, but leave enough room to tilt the unit upright without hitting the ceiling or a wall.
- Skipping the measurements. Before you even buy, measure the room, the doorway and the stairs. Our guides on chest of drawers dimensions and choosing between a chest and a dresser help you get it right the first time.
Why a well-made flat pack makes assembly easier
Assembly is far easier when the pieces are made to fit. Our furniture is manufactured locally in South Africa from A-grade materials, with anti-rust hardware, so the screws and cams that hold your chest together are made to last. Each piece comes with hassle-free assembly instructions, and once your chest is built it is covered by our six-month warranty.
If you are choosing a chest, browse our bedroom furniture range, or look at the Studio 3-Drawer Chest of Drawers. Orders over R5,000 qualify for free nationwide delivery, so a chest and a matching wardrobe or bedside table can arrive together.
For an office or study, our Office and Study range follows the same assembly approach, and our kids furniture suits a child’s room, where careful anchoring matters most.
Our view: build it once, build it right
Home is your identity, and the furniture in it should feel like it belongs there. We have been making furniture in South Africa for over 30 years, and we design our pieces so that the building is part of the pleasure, not a chore.
The mistakes people make with a chest of drawers are rarely about skill. They come from hurrying: tightening before the box is square, fitting one slide a few millimetres higher than the other, skipping the wall anchor because the chest looks sturdy. Slow down for the first hour and the rest goes smoothly.
That is why we use anti-rust hardware and write our instructions to be hassle-free. A screw that holds, a part that fits and a clear order of steps let you finish the job and enjoy the room. Think of us as your great housemate: we hand you the right tools and let you get on with making the space yours.
Hishaam
FAQ
How long does it take to assemble a chest of drawers?
Plan on a couple of hours the first time, and longer for a chest with many drawers. Sorting parts, building each drawer box and fitting the slides take more time than the frame itself. A second pair of hands makes the lifting and final stand-up faster and safer.
What should I do if a drawer will not slide smoothly?
First check that the carcass is square and the cam locks are tight. Then check that the slides on both sides sit at the same height and are parallel. A one or two millimetre adjustment usually fixes it. Open the drawer fully and look for a screw head or a misplaced slide catching.
Do I need to anchor a chest of drawers to the wall?
Yes, particularly where children live. The US Consumer Product Safety Commission advises anchoring furniture to prevent tip-over injuries. Fix the strap into a stud or proper masonry plug, after checking for hidden pipes and cables.
Is a bed frame built the same way as a chest of drawers?
The method is the same: sort the parts, build loosely, square it, then tighten. A bed adds a centre support and slats, which should go in before you place the mattress. Build it with a second person because the rails and headboard are heavy.
Should I empty the drawers before moving the chest?
Take the drawers out and carry them separately, or at least empty them. It makes the chest lighter and stops the drawers sliding open while you carry it. Refit the drawers once the chest is in position and anchored.
Sources
- Home DZINE: DIY chest of drawers
- Home DZINE: Make your own drawers
- Wood Central: Chest of drawers, drawer work
- CPSC: Secure Furniture and TVs, Protect Children
